Clear Type Epoxy Resin Hard Glue – Fast Curing & Waterproof Adhesive for DIY & Industrial Use

Epoxy Resin Hard Glue is a two-component system that cures reliably at room temperature and remains stable even in cooler conditions. It self-levels during application and features natural defoaming, leaving a flat, ripple-free surface with minimal bubbles and a clear, glossy finish once cured. The formulation is optimized against yellowing, holding its color under long-term light exposure and environmental wear better than standard epoxy adhesives. For faster production cycles, curing can be accelerated simply by raising the temperature — no change to the mix ratio required. It’s widely used in crafts and decorative work such as crystal photo frames, cross-stitch frames, handmade ornaments, and name plates, as well as industrial applications like LED strip potting, channel letters, and electronic component encapsulation. It also performs well in deep-pour wood applications like river tables and bar tops. A strong fit for OEM and private-label buyers who need consistent clarity and performance across production runs.

Epoxy Resin Hard Glue is a two-component system built for jobs where clarity and adhesion strength both matter — not one at the expense of the other. The formulation cures reliably at room temperature and holds up well even when temperatures dip, so output quality doesn’t depend on tightly controlled conditions.

What sets it apart in practice is how it behaves during application. The mixture self-levels, spreading out on its own to leave a flat, ripple-free surface rather than requiring extensive tooling. Bubble formation is minimal thanks to its natural defoaming characteristics, which matters most in the pour — a resin that traps air rarely recovers its clarity once cured. The result is a finish with genuine optical clarity and gloss, not just “clear enough.”

Yellowing is where a lot of epoxy adhesives fail over time, and this one is formulated specifically to resist it. Color stability holds up under light exposure and normal environmental wear, so products keep their finished look well past the point where cheaper resins start to amber. Manufacturers needing faster turnaround can raise the curing temperature to shorten cycle times without changing the mix ratio.

Typical uses fall into two broad categories. On the craft and decorative side: crystal photo frames, cross-stitch and painting frames, handmade ornaments, name plates, cards, and similar personalized items where surface appearance is the whole point. On the industrial and electronics side: LED strip potting, LED channel letters, and general component encapsulation, where the resin needs to protect as well as look good. It also holds up for river tables, bar tops, and other wood-and-resin surfaces that call for a deep, glass-like pour.

For OEM and private-label buyers, the combination that matters is clarity, low-temp cure reliability, yellowing resistance, and a workable, self-leveling flow — the four things that actually determine whether a batch performs consistently across production runs, not just in a single test pour.

1.Weigh A and B glue according to the given weight ratio into the prepared cleaned container fully mixed the mixture again the container wall by clockwise, place it along for 3 to 5 minutes and then it can be used.

2.Take the glue according to the usable time and dosage of mixture to avoid wasting. When the temperature is below 15 °C, please heat A glue to 30 ‘C first and then mix it to the B glue (A glue will be thicken in low temperature ), The glue must be sealed lid after use to avoid rejection caused by moisture absorption.

3.When the relative humidity is higher than 85%, the surlace of the cured mixture will absort moisture in the air, and form a layer of white mist in the surface, so when the relative humidity is higher than 85%, is not suitable for room temperature curing, suggest to use the heat curing.

One-Stop Flooring Materials Supplier

High-transparent crystal epoxy resin R & D and production for 10 years.

Over 10 years experience for exporting.

Quality Control : same workers for material feeding and same person to supervise and record data for every batch ; Taking sample to test and mark the details for batch.

ROHS，REACH，CPSIA，BPA，TRA， EN71 ,FDA etc. SA8000 social responsibility system, IS09001 quality system.

We are good at providing solution service for each industry product within 3 days.

Factory Profile

Fast delivery : Capacity production 1000 tons per month , 3~5 days delivery for batch order.

20 sets of automatic production equipment. 5 OEM production lines. Plant area 20000 square meters.

Guangdong Jinhua New Materials Technology Co., Ltd. is a leading manufacturer of 2-components epoxy resin , UV resin ,PU resin etc. in Dongguan China since 2018 and also export raw material of Epoxy resin,hardener, additivesin large scale with very good quality and competitive price. 2-components epoxy resin involves in and apply toArt Craft Jewelry,Deep pour river table and large crafts casting,Tabletop coating,3D and metallic floor coating, labelor sticker doming ,surfboard coating,mold filling ,electric potting etc., they are hot sell and famous for highperformance and good quality : Crystal clear ,bubble free and low odor, yellow resistant etc, received great approval from end users. Especially for art craft resin ,deep pour resin and UV resin etc. , Jincheng has become the preferred supplier for many Amazon sellers.The products meets FDA standard and confirms to ASTM D-4236,all of our products have passed RoHS REACH, CPSIA, PAHS, EN71 ,UL. Jincheng factory implement professional management ,and pass SA8000 and IS09001. Its specialized production equipment and professional R&D team continuously provide customers with stable high quality and market-competitive products. The rigorous QC staff strictly implement the quality control process, test and record each batch of products. With the belief of honest, harmony, creative, preciseness and abundant experi- ence, Jincheng will always offer best solution to worldwide customers. We are looking forward to a mutual beneficial cooperation with the friends all over the world!